In next page click regular or free download and wait certain amount of time (usually around 30 seconds) until download button will appead. Click it and That's it, you're done amigo! Willem eprom programmer pcb50b software download will begin. I recently obtained a willem eprom programmer pcb5.0e. Need help with willem eprom pcb. Currently running Willem Eprom PCB5.0C (0.98D8) software. Sivava.com, EPROM Programmer, PCB. Sivava is the manufacturer of electronic appliances and the distributor of Willem EPROM Programmer online through the.

No sure if I put this in the right place or not. Here goes nothing. I recently obtained a willem eprom programmer pcb5.0e. Currently running Willem Eprom PCB5.0C (0.98D8) software. My question is do I need drivers for this programmer and is this the right software to run this programmer. When I got it, it didn't come with the software and if their was a driver didn't get it.

The software I got off the internet and really not sure if its the right one. Installed the software and when I try to connect the programmer to it. I get an error message 'Hardware error: check power and connections.' Checked all of that and it seems like the everything is plugged in right. When I power the programmer up a green light comes on where is says power, but can't seem to connect the device. Am I missing something. Is there other lights that come on when it powers up.

If I got the wrong softer and need drivers can somebody help me obtain them or send me a link to download them. I included a pic of the programmer I have too. Thanks in advance. Click to expand.Thanks for the website, but I can't seem to download the first one on the list. And all the other ones are not for the pcb5.0e.

They are only for earlier models. Is there some way around it. Some questions.

The DLPortIO only for window 95/98 and nt. For I am running win XP. I can't seem to download it from the website you provided.

I also need to know how to install the software for xp. The 0.97Jb software is that what I need to use with this programmer for it is a pcb5.0E or at least I think it is. The other ones on list does not list my programmer so i'm guessing its not the right software. Really didn't realize this was going to be this hard to install the software.LOL thanks. Click to expand.I got it online on another forum. They Said it worked, but didn't come with cables, manual or disk, but told I could find it on the internet. So, I didn't worry about.

Digging deeper with the dfx pdf. The 15 KHz DC value is 88 + or -2. I dug a beauty of an 1817 cent next to an old piece of iron. I was really surprised with how much deeper I can detect now. So far I have found several that look very promising. Digging deeper with the dfx pdf I wanted to digging deeper with the dfx pdf my first metal detector, and dihging friend who is a bit of a metal detector buff advised me to to to Regton.

Then moved forgot all about until the other day when I was looking for something. And happened to come across it again. So that's where I am at now. Really not sure how to hook it Jup. Meaning do use just USB or printer cable. Or do I use both. I hooked up just the USB and the green light came and stay one.

Then I just hooked up the printer cable and the green comes on, but it's not as bright. Then plugged in both and the green light comes on.

There was a read light that came on beside the green light. It was at the far right side light.

So, I just assumed everything was working when I seen the green light. I did notice when I hook up the USB the computer does find the device like when I hook up other USB devices. It's almost like the programmer isnt being recognized buy the computer.

I do have a bk programmer hooked to the computer to. But I disconnected it though. I didn't know if the computer is having conflicts between the two.

Just a thought. Thank in advance. Click to expand.

I got a power supply. But it still don't seem to be working 100%. Do you know what size power supply is ideal to be able to run all the eproms it can handle. I know I wont use them all, but would like to get a power supply that will handle them all though.

On the board is said 9v to 12v and I got a 9v. Which isnt working. With the 9v ps Got it to finally pick up the device. Thought is was reading the eprom, but when I take it into hexedit. It just shows up with a bunch of this repeating itself.

I bought this programmer about a year ago while working on some Tivos. It works quite well. Now the only guy that actually makes the 5.0E is Kee Electronics.

The REAL/Official willem programmer is made by sivava. Thier latest version is 5.0B. The software that Kee Electronics sends on CD is version 98D12C.